BYPASS / CRUNCH MODE SWITCH:
Engages the unit, allowing the signal to flow through the Go Rocky Go circuit. It also lights up the white LED above it. Hold it for 1.5 seconds to switch from Normal Mode to Crunch Mode (LED turns blue).
ATTACK-SUSTAIN:
The original Conqueror preamp featured a built-in distortion effect with a fuzzy character, quite different from modern distortion pedals and high gain amps, that was the sound of the 60’s!
The Attack-Sustain knob adjusts the amount of gain for the Distortion effect.
• Turn it clockwise for increased saturation and sustain.
Keep in mind that the Go Rocky Go is not two independent pedals in one, to use the Distortion effect, the bypass LED must be lit.
TREBLE:
Adjusts the high-frequency content.
DISTORTION SWITCH:
Activates the Go Rocky Go’s Distortion effect. When Distortion is on, the Dist. Vol potentiometer lights up orange.
BYPASS - NORMAL & CRUNCH MODE :
Engages the unit, allowing the signal to flow through the Go Rocky Go circuit. Hold it for 1.5 seconds to switch from Normal Mode (White LED) to Crunch Mode (Blue LED).
Crunch Gain: Fine-tune the amount of overdrive using the internal control located on the PCB. (Factory set to max.).
M.R.B. LED:
To activate the M.R.B., tap both the Distortion and Bypass footswitches simultaneously. Lights up when the M.R.B. is activated.
VOLUME:
Controls the overall output volume of the Go Rocky Go when the Distortion effect is off.
BASS:
Adjusts the low-frequency content.
DIST. VOL:
The Conqueror’s Distortion circuit had a fixed output volume, making it difficult to balance the clean and distorted levels.We solved this issue by incorporating an independent Distortion Volume control, allowing you to match them, or even make the Distortion effect louder!
M.R.B. SELECTOR:
The Mid-Range Resonant Boost has three selectable frequencies:
• 1 boosts at approximately 500 Hz
• 2 boosts at approximately 700 Hz
• 3 boosts at approximately 1 kHz
This selector switches different capacitors in the resonant circuit, which may produce a slight click noise when adjusting it. To activate the M.R.B., tap both the Distortion and Bypass footswitches simultaneously.
Go Rocky Go Controls
grafic
Created on January 29, 2025
Start designing with a free template
Discover more than 1500 professional designs like these:
View
Essential Business Proposal
View
Project Roadmap Timeline
View
Step-by-Step Timeline: How to Develop an Idea
View
Artificial Intelligence History Timeline
View
Mind Map: The 4 Pillars of Success
View
Big Data: The Data That Drives the World
View
Momentum: Onboarding Presentation
Explore all templates
Transcript
BYPASS / CRUNCH MODE SWITCH:
Engages the unit, allowing the signal to flow through the Go Rocky Go circuit. It also lights up the white LED above it. Hold it for 1.5 seconds to switch from Normal Mode to Crunch Mode (LED turns blue).
ATTACK-SUSTAIN:
The original Conqueror preamp featured a built-in distortion effect with a fuzzy character, quite different from modern distortion pedals and high gain amps, that was the sound of the 60’s! The Attack-Sustain knob adjusts the amount of gain for the Distortion effect. • Turn it clockwise for increased saturation and sustain. Keep in mind that the Go Rocky Go is not two independent pedals in one, to use the Distortion effect, the bypass LED must be lit.
TREBLE:
Adjusts the high-frequency content.
DISTORTION SWITCH:
Activates the Go Rocky Go’s Distortion effect. When Distortion is on, the Dist. Vol potentiometer lights up orange.
BYPASS - NORMAL & CRUNCH MODE :
Engages the unit, allowing the signal to flow through the Go Rocky Go circuit. Hold it for 1.5 seconds to switch from Normal Mode (White LED) to Crunch Mode (Blue LED).
Crunch Gain: Fine-tune the amount of overdrive using the internal control located on the PCB. (Factory set to max.).
M.R.B. LED:
To activate the M.R.B., tap both the Distortion and Bypass footswitches simultaneously. Lights up when the M.R.B. is activated.
VOLUME:
Controls the overall output volume of the Go Rocky Go when the Distortion effect is off.
BASS:
Adjusts the low-frequency content.
DIST. VOL:
The Conqueror’s Distortion circuit had a fixed output volume, making it difficult to balance the clean and distorted levels.We solved this issue by incorporating an independent Distortion Volume control, allowing you to match them, or even make the Distortion effect louder!
M.R.B. SELECTOR:
The Mid-Range Resonant Boost has three selectable frequencies: • 1 boosts at approximately 500 Hz • 2 boosts at approximately 700 Hz • 3 boosts at approximately 1 kHz This selector switches different capacitors in the resonant circuit, which may produce a slight click noise when adjusting it. To activate the M.R.B., tap both the Distortion and Bypass footswitches simultaneously.