Want to make interactive content? It’s easy in Genially!

Transcript

ECITB Level 3 Pipefitting RQF

Start

Lennon Wiley Technical Discussion

Index

Home

IPS01

IPS02

IPS03

IPS04

IPS05

IPS07

IPS08

IPS10

IPS11

IPS01

Home

L3B0104-K30 Which of these is a consequence of not following procedures? L3B0115-B3 Which of the following statements about communication is not true? L3A0111-K18 If risk is the likelihood and consequences of a hazard, which of the following is a risk? L3A0104-K2 A Risk Assessment is... L3A0108-K7 What is accepted to be our last line of defence to prevent exposure to a hazard? L3A0118-K10 The purpose of a lock-out/tagging system is to L3A0102-K1 A written Health and Safety policy..

PF0207-K1 Where would you find information on which type of grease to use when assembling a valve stem? PF0237-K1 You are working on top of a boiler and need to install a valve on top of the unit, where would you find information about the safety whilst conducting this task? select two answers L30247-K10 Which 2 of the following should be included in the handover information? L30212-K5 Why do planned preventative maintenance programmes benefit companies? L30254-K1 What is meant by the term legislative requirements?

IPS02

Home

PF0326-K6 Which pattern development methods is shown in the picture? PF0308-K2 How is the minimum bend radius of a pipe usually approximately calculated? PF0338-K2 The pictured pipe bracket is presented in which drawing type? PF0302-K4 A template is to be positioned on a pipe but the centre finder is NOT available, what else can be used to accurately mark the centre line? PF0325-K4 Use the diagram to help calculate the approximate advance between the angles of the offset if the travel is 100mm and the set is 40mm.

IPS03

Home

PF0404-K2 Which tool is best suited for removing burrs from the internal edge of a cut 25mm diameter thin wall copper tube? PF0408-K3 From the list given select the most accurate tooling for checking the pitch of a pipe thread PF0418-K4 The machined edge of a piece of carbon steel has turned blue due to over heating, what effect does this have on the material characteristics?

IPS04

Home

PF0503-K2 Complete this sentence -- To help prevent side wall damage the former must be _______ on to the bending machine piston head ramPF0509-K2 Which type of operating fluid medium is used in a hydraulic bending machine?PF0522-K3 How should a large uneven section heavy carbon steel pipe be supported during bending operations? PF0535-K8 The copper pipe in the picture has suffered creasing on the inside radius, what is most likely the cause? PF0507-K7 You are sizing up material for a job, what would be the approximate length needed to for a 90 degrees bend length with a centre line radius of 200mm?

IPS05

Home

PF0701-K1 When tacking together thick walled steel pipes ready for butt welding operations, what is the preferred method used? PF0703-K1 Which type of gasket is recommended for sealing high pressure steam flange connections and components? PF0714-K2 The picture shows a type of sealing joint, what type of flanged connection would it be used in? PF0722-K2 Which type of tool shown in the picture? PF0719-K5 An isometric drawing of a pipe system has 1:80 annotated next to it, what does this represent? PF0705-K6 During an assembly you identify what you think is a welded joint defect, what would you recommend to confirm this? PF0716-K7 What is the General specification for carbon steel based pipe work?

IPS07

Home

PF0819-K1 Which type of gasket is recommended for sealing high pressure steam flange connections? PF0802-K2 The drop in pipe level by introducing a Rise is otherwise know as what? PF0814-K3 The image shows a damaged O seal, what is the most likely cause of the damage? PF0810-K4 When positioning a new pipe spool it is suspected that there is an asbestos gasket on the existing pipe flange, what should be done about this?

IPS08

Home

PF1061-K1 Which document is required to be applied for before a high pressure hydraulic test can be carried out? PF1004-K2 Which document is strictly followed to ensue that the component assembly meets compliance? PF1006-K2 What is a Hold Point? PF1009-K3 When taking accurate positional measurements of a pipe spool position, what reference is used? PF1014-K5 An adequate but unspecified component has been fitted to a pipe system, which document is issued to accept this change in design? PF1044-K6 When you have completed a hydrostatic pressure testing on a high pressure hydraulic oil system, what is the next recommended procedure? PF1049-K6 Typically what hazard remains after X-ray inspection? PF1051-K8 During final inspections a plastic pipe is discovered to have been damaged and has a small crack, what is the industry recommended course of action?

IPS10

Home

PF1128-K6 Which two of the following are preferred methods for marking pipes for reuse? PF1130-K3 Why is it important to provide engineered supports to components during dismantling operations? PF1105-K2 Before you use an abrasive cutter on an old pipe system, what should you check? PF1118-K5 The picture shows damage to a flange face, what is most likely to have caused this damage? PF1101-K9 Where should you go to check that an old pipe system is safely isolated before starting dismantling activities? PF1103-K9 From the options given, prior to dismantling a pipe system you should check what? PF1113-K9 Which document will provide details on how to identify removed components?

Home

IPS11