Technical discussion

Ryan Wild Technical Discussion

Start

ECITB Level 3 Pipefitting RQF

IPS11

IPS10

IPS08

IPS07

IPS05

IPS04

IPS03

IPS02

IPS01

Home

Index

L3B0109-K36 Why should you use resources efficiently and effectively? L3B0122-K16 Your colleague trips and falls, unfortunately driving a screwdriver though a hand. Your first action should be: L3B0104-K30 Which of these is a consequence of not following procedures? L3B0103-K28 Which of these methods can be used to establish and maintain good working relationships? (Choose two) L3A0121-K38 Which of the following is NOT a cause of environmental pollution?

Home

IPS01

Home

IPS02

PF0237-K1 You are working on top of a boiler and need to install a valve on top of the unit, where would you find information about the safety whilst conducting this task? select two answers L30249-K13 What is the purpose of using Intrinsically Safe equipment? L30246-K10 Handover information forms part of which file? L30266-K15 What method is best suited to checking materials are to the specification quality and quantity? L30241-K17 Which of the following documents covers the removal and disposal of electrical waste?

Home

IPS03

PF0336-K1 Which is considered the most important information on an engineering drawing used when fabricating a pipe section? PF0308-K2 How is the minimum bend radius of a pipe usually approximately calculated? PF0330-K3 When preparing for marking out a stainless steel pipe template, which of the following would be the best marking medium? PF0309-K4 How can the side centres of a pipe section be easily located in reference to the top centre line? MF0334-K5 The picture shows a pipe loop, what datum point should you use to verify the bend radius?

Home

IPS03

PF0336-K1 Which is considered the most important information on an engineering drawing used when fabricating a pipe section? PF0308-K2 How is the minimum bend radius of a pipe usually approximately calculated? PF0330-K3 When preparing for marking out a stainless steel pipe template, which of the following would be the best marking medium? PF0309-K4 How can the side centres of a pipe section be easily located in reference to the top centre line? MF0334-K5 The picture shows a pipe loop, what datum point should you use to verify the bend radius?

Home

IPS04

PF0427-K2 What extra precaution should be taken in to consideration when using a chop saw to cut a section of GRP pipe? PF0408-K3 From the list given select the most accurate tooling for checking the pitch of a pipe thread PF0418-K4 The machined edge of a piece of carbon steel has turned blue due to over heating, what effect does this have on the material characteristics? PF0412-K4 A section of in service 10mm plastic tube appears to have a crease and is permanently bent, what could have caused this defect? PF0439-K5 In which document would you find information on how to fabricate a threaded pipe connection?

Home

IPS05

PF0509-K2 Which type of operating fluid medium is used in a hydraulic bending machine? PF0530-K2 When the stresses on the outside radius overcomes the ability of the tube cross section to support it - What is this describing? PF0503-K2 Complete this sentence -- To help prevent side wall damage the former must be _______ on to the bending machine piston head ram PF0539-K9 Name the pictured instrument used for verifying pipe bend angles? PF0537-K8 A completed thick wall carbon steel hydraulically formed bend is being inspected, which area should the most attention be given? PF0507-K7 You are sizing up material for a job, what would be the approximate length needed to for a 90 degrees bend length with a centre line radius of 200mm?

Home

IPS07

PF0703-K1 Which type of gasket is recommended for sealing high pressure steam flange connections and components? PF0717-K2 A two metre length of thick wall 6 inch stainless steel pipe is to be aligned to a valve, how would the pipe be best supported? PF0707-K2 What should be first carried out before using a torque wrench? PF0714-K2 The picture shows a type of sealing joint, what type of flanged connection would it be used in? PF0719-K5 An isometric drawing of a pipe system has 1:80 annotated next to it, what does this represent? Give me an example of what would indicate the slope or gradient of a pipe?

PF0819-K1 Which type of gasket is recommended for sealing high pressure steam flange connections? PF0802-K2 The drop in pipe level by introducing a Rise is otherwise know as what? PF0805-K2 The picture shows a valve commonly fitted to pipe systems, what type is it? PF0829-K2 You have just assembled and installed the pictured expansion joint, what should be done next? Pressure test. PF0820-K4 Where should the final set positions of a spring loaded pipe hanger be recorded? . PF0806-K4 In which document would you find information about how to install pipe components in a system?

Home

IPS08

Home

IPS10

PF1040-K3 The process by which safety valves are isolated from the system under a pressure test is called? PF1010-K3 If a length of pipework is 50 meters long and has a Rise of 0.5 meters, what is the slope? PF1014-K5 An adequate but unspecified component has been fitted to a pipe system, which document is issued to accept this change in design? PF1044-K6 When you have completed a hydrostatic pressure testing on a high pressure hydraulic oil system, what is the next recommended procedure?

IPS11

Home

PF1130-K3 Why is it important to provide engineered supports to components during dismantling operations? PF1128-K6 Which two of the following are preferred methods for marking pipes for reuse? PF1119-K1 A high rated spring loaded pipe hanger needs to be removed before the pipe section is cut away, what should be done? select two answers PF1126-K4 Which of the following is breaking containment? PF1118-K5 The picture shows damage to a flange face, what is most likely to have caused this damage? PF1101-K9 Where should you go to check that an old pipe system is safely isolated before starting dismantling activities?