Basic Interactive Microsite
Pipefitters Group 2
Created on July 19, 2024
More creations to inspire you
Transcript
ECITB Level 2 Diploma in Supporting the Installation of Engineering Construction Plant and Systems (RQF) - Plating
Start
Adam Walker SmithTechnical discussion
Index
Home
SIPS01
SIPS07
SIPS02
SIPS03
SIPS05
SIPS08
SIPS04
SIPS06
L3B0111-K30Which of these is not true about toolbox talks?L3B0104-K30Which of these is a consequence of not following procedures?L3B0109-K36Why should you use resources efficiently and effectively? L3B0115-B3Which of the following statements about communication is not true?L3B0122-K16Your colleague trips and falls, unfortunately driving a screwdriver though a hand. Your first action should be:L3B0101-K35An employer's obligation to make sure its actions protect and improve society's welfare as well as its own interests is referred to as: L3A0103-K2The Management of Health & Safety at Work Regulations require a risk assessment which is: L3A0119-K10When we talk about Isolation of energy we mainly think about electricity, what other items could we consider when thinking about isolation practices?
SIPS01
Home
L20229-K6A drawing is found to be altered and covered in hand written notes, do you still use it?L20243-K7Who will be required to sign a work permit?L20219-K14How should materials be handled and prepared for use?L20264-K11What procedures can be used to ensure safe and correct connection and operation of mains services?L20220-K14What are typical material handling techniques? Select two answers
SIPS02
Home
PL0318-K2 Why are tolerances stated on the engineering drawings?PL0302-K4 When marking out a stainless steel plate what would be the correct marking medium to use?PL0328-K4Why should measuring instruments such as steel tape measures and steel rulers should be checked for calibration at regular intervals?
SIPS03
Home
PL0402-K1What is the most suitable method used to prepare material for a V butt weld?PL0422-K1 The term for the width of cut produced by any thermal cutting process is?PL0425-K3 What are the most common types of injury encountered when using a cold chisel to remove metal?
SIPS04
Home
PL0517-K2What is the purpose of using a 'pre-set' on materials during assembly? SIPS0507-K1 Why is it important to add revision details to drawings?SIPS0509-K1What is the key safety document to be complete and signed by authorised persons before starting work?PL0516-K2Which welding process is usually used on site to tack weld sections together?PL0518-K2What is a tirfor used for in engineering construction?
SIPS05
Home
PL0613-K2What is a transition piece used for during positioning and installation?PL0626-K2During the positioning and installation of fabricated bridge sections, why are the open ends covered by blanking plates?PL0620-K1Once the components are installed in their designated position, what method is used to verify compliance?PL0611-K1When installing large, heavy formed sections into position, what is a primary consideration?
SIPS06
Home
PL0728-K1When using a reciprocating saw to remove seized nuts why is it best practice to cut into the nut, not the washer?PL0713-K2What method is used to remove torque control bolts from a joint during dismantling?
SIPS07
Home
SIPS0831-K5What is the name of the tool pictured below?SIPS0846-K5Which would be the most suitable tool for measuring the height of a weld bead contour?SIPS0805-K1A plate butt weld in the HORIZONTAL position has the abbreviation of what?SIPS0835-K6What is the weld defect illustrated below?SIPS0820-K2The choice of shielding gas in MIG / GMAW welding depends primarily on what?
SIPS08
Home